Whirlpool announced it back in July; I was able to order it in October; and it wasn’t delivered until January 21st — but I now own a real live, made for the U.S. market, heat-pump clothes dryer. It’s officially the .
Heat-pump clothes dryers have been available for many years in Europe, but this dryer and another recently announced model from LG are the first to hit the U.S. market. I chose the Whirlpool over the LG primarily because the LG, for some reason, still has a vent to the outdoors. One of the major advantages of incorporating a heat pump into a clothes dryer is that the dryer can be ventless. For a tight building enclosure that means one fewer penetration to be sealed. It also means that the dryer isn’t taking conditioned air from the living space and venting it to the outdoors.
The dryer (see Image #1, above) looks pretty much like every other clothes dryer, doesn’t it? From this angle, the only difference you can really see between a standard dryer and this dryer is the panel at the bottom right which open to allow access to the secondary lint filter.
But look at the washing machine outlet box at left. The two steel-braided hoses and the large black drain hose come from the washing machine. But that small copper tube attached to the small black hose is the drain from the dryer.
I ran a medium-large load using the most efficient cycle and, well, it worked. It didn’t seem to take terribly long (although I didn’t time it) and the clothes came out not just dry but quite soft and with fewer wrinkles than the laundry from the last dryer I owned. In fact, the towels came out positively luxuriously soft. It is a bit louder than your typical dryer, though — something to keep in mind if your dryer isn’t located in an acoustically isolated area of your house.
The real downside to the dryer is the cost. I got it from for $1,399 with free shipping. That’s a lot for a dryer. Of course, I’ll save money every time I run a load, at least, compared to a traditional dryer, right? To figure out how much I created a . It takes into account the amount of energy each dryer requires to run, the amount of energy a minisplit heating system would use to heat/cool the makeup air (for a venting dryer) and the fact that all of the energy used to run a heat-pump dryer stays in the house. This latter effect is a significant savings in the heating season and a significant cost in the cooling season.
According to these calculations, and based on prices for electricity and gas in Massachusetts, the costs per load are:
|Traditional electric dryer||55¢||53¢|
|Traditional gas dryer||39¢||38¢|
|Heat pump electric dryer||17¢||33¢|
For a family that does five five loads of drying a week, that’s a savings of $1.90 per week during the winter and $1.00 per week during the summer for a heat-pump dryer vs. a traditional electric. Averaged out that comes to a savings of about $75 per year, which would bring the total lifetime cost of a heat pump dryer much closer to the cost of a traditional dryer. But unless you live in a very cold climate or dry an excessive amount of laundry, a heat-pump dryer, at today’s prices, is unlikely to save you a lot of money. If prices come down, or if the price of energy goes up, that could change.
While the cost may or may not be an issue, one great feature of this dryer that could turn it into a mainstream product is how much gentler it is on your clothes. Because it’s not using heat alone to dry the clothes, it doesn’t heat the air as much as a traditional dryer. Not only will clothes last longer but it might make it possible to dry clothes that you would otherwise need to hang dry.
How heat-pump clothes dryers work
A traditional dryer works by heating air, blowing it into the drum chamber (where it absorbs moisture from the clothes), and then exhausting the now moisture-laden hot air out of the dryer and out of the house.
A condensing dryer, on the other hand, works by heating air, blowing it into the drum chamber and then pulling that warm moist air from the drum and cooling it to the point that the moisture condenses and drips into a collection tray. The cool dry air is then heated and recirculated back into the drum where it again picks up moisture and the cycle continues.
The tricky thing with a condensing dryer is how to cool the air being pulled from the drum. Some condensing dryers use a metal plate that is air-cooled and some use a scheme that requires a steady supply of cold water. Neither of these systems results in a dryer that is any more energy-efficient than a traditional dryer, and the appliances are much slower. The market for condensing dryers has typically been for apartment buildings where running an exhaust vent isn’t feasible.
A heat-pump dryer is a kind of condensing dryer. Like pretty much every heat pump device, the heat pump in a heat pump clothes dryer has a cold coil and a hot coil. This works out perfectly for a condensing dryer as the cold coil can be used to cool the warm moist air coming from the drum (and to provide a condensing surface for the moisture in the air) and the hot coil can be used to heat the air before sending it back.
Heat pump clothes dryers use 40% to 50% as much electricity as a traditional electric dryer and dry clothes much faster than condensing dryers that don’t use heat pumps, while still being slower than a conventional gas or electric dryer.
Joe Rice is a retired software engineer who recently moved into his energy-efficient house in eastern Massachusetts. His blog about the construction and performance of the house is called .